july 2013 3-terminal filters for power line ach series ach32c [1206 inch]* ach3218 [1207 inch] * dimensions code jis[eia] emc components
(2/9) 001-01 / 20130722 / e9611_ach.fm emc components reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 12 months. be sure to follow the storage conditions (temperature: 5 to 40c, humidity: 10 to 7 5% rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (cars, electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders
(3/9) 001-01 / 20130722 / e9611_ach.fm ? all specifications are subject to change without notice. emc components 3-terminal filters for power line features t-type emc filter that can be used for high-current circuits. achieve excellent attenuation characteristics by using it for circuits with stable grounds. does not require mounting space due to vertical mounti ng design, making it perfect for high-density circuits. guaranteed temperature range is C40 to +125c, so it can be used under severe env ironmental conditions. use this product under reflow soldering conditions. application he devices (tvs, vtrs, cd players, electronic musical instruments, pcs, etc.) oa equipment (computers, terminals, facsimiles, etc.) fa equipment (robots, nc machine tools, process controllers, etc.) ae equipment (car navigation systems, ecus, etc.) ach32c cannot be used for ecus. part number construction ach32c ach3218 operating temperature range, package quantity, product weight the storage temperature range is for after the circuit board is mounted. overview of the ach series ach 32c - 103 - t 001 series name lwt dimensions capacitance packaging style internal code (mm) (pf) 32c 3.21.62.1 100 10 t taping 103 10000 ach 3218 - 223 - t ??? series name lwt dimensions capacitance packaging style internal code (mm) (pf) 3218 3.21.82.5 223 22000 t taping type temperature range package quantity individual weight operating temperature storage temperature c c pieces/reel mg ach32c C40 to +125 C40 to +125 2,000 70 ach3218 C40 to +125 C40 to +125 1,000 70 product compatible with rohs directive halogen-free compatible with lead-free solders rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://www.t dk.co.jp/rohs/ halogen-free: indicates that cl content is less than 900ppm, br content is less than 900ppm, and that the total cl and br conte nt is less than 1500ppm.
(4/9) 001-01 / 20130722 / e9611_ach.fm ? all specifications are subject to change without notice. emc components overview of the ach series recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 60 to 120s 230c 30 to 60s 250 to 260c 10s max. natural cooling t3 t1 preheating t2 soldering t3 t3 t4 t2 t1 t: time peak t: temperature
(5/9) 001-01 / 20130722 / e9611_ach.fm ? all specifications are subject to change without notice. emc components ach series ach32c type shape & dimensions recommended land pattern circuit diagram 1.6 0.2 3.2 0.2 2.1 0.2 13 2 0.1 dimensions in mm 0.6 4.2 1.0 1.0 0.5 2.6 dimensions in mm ? no polarity 3 1 2 gnd
(6/9) 001-01 / 20130722 / e9611_ach.fm ? all specifications are subject to change without notice. emc components ach series y ach32c type electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. insertion loss vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. rated voltage (v)max. rated current (a)max. insulation resistance (m )min. dc resistance (m )max. guaranteed insertion loss (db) guaranteed frequency bandwidth (mhz) part no. 50 6 100 2 C15 2000 to 6000 ach32c-100-t001 50 6 100 2 C15 1300 to 2500 ach32c-220-t001 50 6 100 2 C15 650 to 2500 ach32c-470-t001 50 6 100 2 C20 450 to 1300 ach32c-101-t001 50 6 100 2 C20 200 to 800 ach32c-331-t001 50 6 100 2 C25 100 to 350 ach32c-102-t001 50 6 100 2 C25 55 to 300 ach32c-222-t001 50 6 100 2 C25 30 to 200 ach32c-103-t001 50 6 100 2 C25 10 to 300 ach32c-333-t001 50 6 100 2 C25 3.5 to 200 ach32c-104-t001 measurement item product no. manufacturer insertion loss e5071b agilent technologies dc resistance 4338a agilent technologies insulation resistance 4339a agilent technologies product no. manufacturer e5071b agilent technologies 1 80 70 60 50 40 30 20 10 0 10 100 1000 10000 insertion loss ( db ) frequency ( mhz ) 104 103 102 333 222 331 100 220 470 101
(7/9) 001-01 / 20130722 / e9611_ach.fm ? all specifications are subject to change without notice. emc components ach series ach3218 type shape & dimensions recommended land pattern circuit diagram 3.2 0.3 2.5 0.25 0.6 1.8 0.2 0.45 dimensions in mm 1.4 2.2 1.4 1.94 0.6 dimensions in mm ? no polarity 3 1 2 gnd
(8/9) 001-01 / 20130722 / e9611_ach.fm ? all specifications are subject to change without notice. emc components ach series y ach3218 type electrical characteristics characteristics specification table insertion loss vs. frequency characteristics insertion loss 25db frequency range (mhz) rated voltage (v)max. rated current (a)max. dc resistance ( )max. [terminal no.1 to 3] insulation resistance (m )min. [terminal no.1 to 2/no.2 to 3] part no. 11 to 55 20 1.5 0.06 1000 ach3218-223-t ??? 17 to 60 20 1.5 0.06 1000 ach3218-103-t ??? 22 to 75 20 1.5 0.06 1000 ach3218-682-t ??? 30 to 85 20 1.5 0.06 1000 ach3218-472-t ??? 37 to 90 20 1.5 0.06 1000 ach3218-332-t ??? 45 to 105 20 1.5 0.06 1000 ach3218-222-t ??? 60 to 115 20 1.5 0.06 1000 ach3218-152-t ??? 80 to 140 20 1.5 0.06 1000 ach3218-102-t ??? 95 to 150 20 1.5 0.06 1000 ach3218-681-t ??? 120 to 180 20 1.5 0.06 1000 ach3218-471-t ??? 130 to 210 20 1.5 0.06 1000 ach3218-331-t ??? 170 to 250 20 1.5 0.06 1000 ach3218-221-t ??? 205 to 280 20 1.5 0.06 1000 ach3218-151-t ??? 265 to 340 20 1.5 0.06 1000 ach3218-101-t ??? 340 to 420 20 1.5 0.06 1000 ach3218-680-t ??? 420 to 500 20 1.5 0.06 1000 ach3218-470-t ??? 500 to 600 20 1.5 0.06 1000 ach3218-330-t ??? 600 to 700 20 1.5 0.06 1000 ACH3218-220-T ??? 50 40 30 20 10 0 1000 100 300 10 30 13 insertion loss ( db ) frequency ( mhz ) 223 103 472 682 332 222 152 102 331 471 681 221 151 101 680 470 330 220
(9/9) 001-01 / 20130722 / e9611_ach.fm ? all specifications are subject to change without notice. emc components ach series packaging style reel dimensions tape dimensions ach32c type ach3218 type ty p e w1 w2 ach32c 90.3 13+1.4 ach3218 13.00.3 17.00.4 dimensions in mm type a b f w k ach32c 1.90.1 3.50.1 3.50.05 8.00.2 2.30.1 ach3218 2.20.1 3.70.05 5.50.05 12.00.3 3.15max. 2.0 0.5 ?13 0.2 ?21 0.8 ?60min. w2 dimensions in mm w1 1.0 ?180 +0 C3 b a 8.00.3 f 1.750.1 4.00.1 4.00.1 2.00.05 1.5 +0.1 0 k dimensions in mm 160min. taping 440min. drawing direction 500 to 560min. 40 to 80 taping 200min. 300min. drawing direction dimensions in mm
|
